NPT, BSPT and BSPP pipe threads are not automatically interchangeable, even when their nominal sizes match. NPT uses a 60-degree thread profile, while BSP threads use a 55-degree profile. BSPT connections are associated with ISO 7-1 thread-sealing designations; BSPP commonly refers to ISO 228-1 parallel G threads, which require a separate sealing interface for pressure-tight service.
When replacing a fitting, check the complete thread designation, the male and female connections, and where the joint is intended to seal. A threaded connection that turns together is not necessarily a suitable pressure joint.
NPT vs BSPT vs BSPP: Quick Comparison
| Thread family | Form | Designation | Sealing principle |
|---|---|---|---|
| NPT | 60°, tapered 1:16 on diameter | NPT | Tapered thread with approved sealant |
| ISO 7-1 / BSPT family | 55°; tapered or parallel mating threads | R, Rc, Rp | Specified thread-sealing connection |
| ISO 228-1 / BSPP | 55°, parallel | G | Seal outside the threads |
Both NPT and R tapered threads have a nominal 1:16 taper on diameter. Their thread forms, dimensions and acceptance requirements differ. NPT is specified by ASME B1.20.1.
What Do R, Rc, Rp and G Mean?
The individual thread designation matters more than a generic BSP label. Under ISO 7-1, R denotes an external tapered thread, Rc an internal tapered thread and Rp an internal parallel thread. G denotes a parallel thread under ISO 228-1; both male and female G threads are parallel.
| Mark | Thread | Form | Standard |
|---|---|---|---|
| R | External | Tapered | ISO 7-1 |
| Rc | Internal | Tapered | ISO 7-1 |
| Rp | Internal | Parallel | ISO 7-1 |
| G | External or internal | Parallel | ISO 228-1 |
Rp and G are both parallel, but they belong to different connection specifications. ISO 7-1 addresses connections intended to be pressure-tight on the threads. ISO 228-1 covers parallel threads whose pressure seal is achieved outside the threads. A matching nominal size does not establish an acceptable substitution.
Which BSP Thread Combinations Can Seal?
R/Rc and R/Rp are recognized ISO 7-1 mating combinations when the parts meet the applicable requirements. Sealant selection and assembly instructions depend on the actual fitting and service. For a G connection, the thread primarily provides mechanical engagement and compression of a separately designed seal.
Do not treat a G female port as interchangeable with an Rp female port merely because both are parallel. Also, PTFE tape cannot replace a missing gasket, O-ring or seating surface in an assembly that relies on an external seal.
NPT vs BSP Thread Size Differences
Pitch is a practical first check, although it does not establish the complete thread designation. At 1/2 and 3/4 inch, NPT and BSP both have 14 threads per inch, so examining the profile and connection specification becomes especially important.
| Nominal size | NPT TPI | BSP TPI |
|---|---|---|
| 1/8 | 27 | 28 |
| 1/4 | 18 | 19 |
| 3/8 | 18 | 19 |
| 1/2 | 14 | 14 |
| 3/4 | 14 | 14 |
| 1 | 11.5 | 11 |
| 1-1/4 | 11.5 | 11 |
| 2 | 11.5 | 11 |
For NPT dimensions, nominal pipe outside diameters and measurement steps, refer to the existing NPT Thread Chart. This article concentrates on connection selection rather than repeating that size chart.
Can NPT and BSP Threads Be Connected?
Do not specify a direct NPT-to-BSP connection as an interchangeable joint. In some sizes, the threads may engage partially, but the different thread profiles and dimensional requirements do not establish an approved pressure connection. An apparently tight joint may leak or damage the mating parts.
Use an appropriately rated transition adapter with an NPT end and the correctly designated R, Rc, Rp or G interface at the other end. Each connection must use its intended sealing method. Extra sealant or torque is not a substitute for matching the specified thread and seal.
NPTF is a separate Dryseal thread series; its compatibility with NPT is addressed in LILY Bearing's NPT vs NPTF guide. The two subjects should not be confused.
How to Identify an Unknown NPT or BSP Thread
Begin with the part marking and drawing. Record the nominal size and whether the connection is male or female, check pitch with a thread gauge, determine whether it is tapered or parallel, and examine its thread profile. At 1/2 and 3/4 inch, 14 TPI is shared by NPT and BSP, so pitch alone is insufficient.
LILY's product catalog provides three useful examples: BEFFNBFI (NPT), JBFBKDGG (BSPT) and the BSPP-listed JBFBKDHF in the high-pressure plated brass pipe range. Their catalog thread designations, not visual similarity, are the reliable way to distinguish these examples.
Calipers and pitch gauges are useful for preliminary identification but do not prove manufacturing compliance. ISO 7-2 describes limit-gauge verification for ISO 7-1 threads. Use the approved drawing and applicable inspection procedure where conformity is important.
How to Specify a Pipe Thread Adapter
Describe both ends independently. For example, specify a 1/2-14 NPT male connection on one side and an R 1/2 male connection on the other. Add the material, required pressure-temperature capability, medium and sealing instructions. For G-thread connections, specify the correct sealing face or bonded washer arrangement, not just the G size.
A real product example is LILY FIDCTBEE BSPT × NPT adapter. Its product specification lists 1/2-inch pipe size, male threads on both ends, 3-inch length, 230 brass construction and BSPT × NPT thread types. Confirm which end has each designation and the complete installation requirements from the approved drawing before ordering.
For a wider choice of materials and connection types, browse LILY Bearing's pipe fittings category. The steel threaded pipe range provides additional NPT components; the thread designation and suitability of each product still need to be checked separately.
Frequently Asked Questions
Is R 1/2 the Same as BSPT 1/2?
R 1/2 identifies an external tapered pipe thread under ISO 7-1. BSPT is a broader conventional term for the corresponding thread-sealing family. Use R 1/2 when an exact male-thread designation is required.
Can a G Male Thread Seal in an Rc Female Port?
Do not assume so. G is a parallel ISO 228-1 thread, while Rc is a tapered ISO 7-1 internal thread. Even with the same nominal size, they are not an automatically qualified pressure-sealing combination.
Can PTFE Tape Replace a BSPP Sealing Washer?
No. If the specified G-thread assembly seals at a gasket, bonded washer or O-ring seat, that sealing element and its mating surface must be present and suitable. Thread tape does not replace them.
Are NPT and BSPT Interchangeable at 1/2 Inch?
No. They share a nominal 14 TPI but have different included thread angles: 60 degrees for NPT and 55 degrees for BSPT. Use a specified transition connection rather than relying on apparent engagement.
Technical References
ASME B1.20.1 — Pipe Threads, General Purpose, Inch; ISO 7-1 — Pipe Threads Where Pressure-Tight Joints Are Made on the Threads; ISO 7-2 — Verification by Means of Limit Gauges; and ISO 228-1 — Pipe Threads Where Pressure-Tight Joints Are Not Made on the Threads. Official standard pages are linked in the relevant sections above.







